Lief.martin: Updated release notes

2018-05-18T04:14:28Z

Updated release notes

←Older revision		Revision as of 04:14, 18 May 2018
Line 3:		Line 3:
	! Key !! Release Notes		! Key !! Release Notes
	\|-		\|-
	~~\| QPM-1709 \|\| "Relative Compaction" (AS 1289.5.4.1) test is now "Compaction Control Test-Dry Density Ratio, moisture variation and moisture ratio" (AS 1289.5.4.1) to align with Australian Standards~~		! Key !! Linked Issues !! Release Notes
	\|-		\|-
	\| QPM-~~1854~~ \|\| ~~Assigned Maximum~~ Dry Density ~~test now uses the correct tolerance for OMC in accordance with the standard (~~1289.5.4.2)		\| QPM-1709 \|\| QPS-737 \|\| The name used of the AS 1289.5.4.1 test has been changed from Relative Compaction [AS 1289.5.4.1] to Compaction Control Test-Dry Density Ratio, moisture variation and moisture ratio [AS 1289.5.4.1] to align with Australian Standards.
	\|-		\|-
	\| QPM-~~1867~~ \|\| ~~QESTField Scheduler no longer fails to load technicians~~ when ~~attempting to use a laboratory with no field technicians~~.		\| QPM-1854 \|\| QPS-1006 \|\| The Assigned Maximum Dry Density [AS 1289.5.4.2] test now uses the tolerances for OMC listed in Table 1 of the AS 1289.5.4.2 standard. Previously a bug resulted in a tolerance of 1.0% being used even when it should have been higher.
	\|-		\|-
	\| QPM-~~1875~~ \|\| ~~External documents (printable worksheets, dynamic worksheets, external test reports, etc) no longer make use of long~~-~~lived record~~-~~sets. This helps to avoid a situation where a database transaction would be committed or rolled back while the record set is still in use, resulting in~~ an ~~error message "Catastrophic Failure".~~		\| QPM-1867 \|\| QPS-1038 \|\| QESTField Scheduler - Fixed an bug that resulted in an error when attempting to access the schedule for a laboratory with no field technicians.
			Error fetching technicians: Exception has been thrown by the target of an invocation.
	~~Note~~ that ~~there are still other situations~~ in ~~QESTLab where this same~~ error ~~is known~~ to ~~occur, specifically QPM-1578, which can occur on some test screens if~~ the ~~screen is unloaded while~~ the ~~contents~~ of ~~dropdown list is loading~~.
	\|-		\|-
	\| QPM-~~1879~~ \|\| ~~The QESTField Start Curing Workflow for now uses~~ the QESTLab ~~Non Standard Curing Reasons~~ list ~~for its non standard curing reason selection for Australian Concrete Samples~~.		\| QPM-1875 \|\|QPS-1041, QPS-1030, QPM-1907, QPM-1578 \|\| External documents (printable worksheets, dynamic worksheets, external test reports, etc) no longer make use of long-lived record-sets. This helps to avoid a situation where a database transaction would be committed or rolled back while the record set is still in use, resulting in an error message "Catastrophic Failure".
			Note that there are still other situations in QESTLab where this same error is known to occur, specifically
			QPM-1578 OPEN , which can occur on some test screens if the screen is unloaded while the contents of dropdown list is loading.
	\|-		\|-
	\| QPM-1882 \|\| ~~Reduced maximum density screens (~~1289.5.1.~~1 &~~ 1289.5.2.1~~) are now able to be used in Assigned Maximum Density (~~AS 1289.5.4.~~2) calculations~~.		\| QPM-1879 \|\| QPS-1093 \|\| In QESTField, the Start Curing workflow for Concrete has been updated to use the QESTLab list Reason Non Standard, rather than a predefined set of values.
			\|-
			\| QPM-1882 \|\| \|\| The Assigned Maximum Density [AS 1289.5.4.2] screen has been updated to allow the results of reduced test screens to be imported. Results can be imported from both the "standard effort" Maximum Dry Density [AS 1289.5.1.1] * and "modified effort" Maximum Dry Density [AS 1289.5.2.1] * tests.
	\|}		\|}

Stephen.riddell at 06:58, 11 May 2018

2018-05-11T06:58:02Z

New page

==QEST Platform 4.6.3051==
{| class="wikitable"
! Key !! Release Notes
|-
| QPM-1709 || "Relative Compaction" (AS 1289.5.4.1) test is now "Compaction Control Test-Dry Density Ratio, moisture variation and moisture ratio" (AS 1289.5.4.1) to align with Australian Standards
|-
| QPM-1854 || Assigned Maximum Dry Density test now uses the correct tolerance for OMC in accordance with the standard (1289.5.4.2)
|-
| QPM-1867 || QESTField Scheduler no longer fails to load technicians when attempting to use a laboratory with no field technicians.
|-
| QPM-1875 || External documents (printable worksheets, dynamic worksheets, external test reports, etc) no longer make use of long-lived record-sets. This helps to avoid a situation where a database transaction would be committed or rolled back while the record set is still in use, resulting in an error message "Catastrophic Failure".

Note that there are still other situations in QESTLab where this same error is known to occur, specifically QPM-1578, which can occur on some test screens if the screen is unloaded while the contents of dropdown list is loading.
|-
| QPM-1879 || The QESTField Start Curing Workflow for now uses the QESTLab Non Standard Curing Reasons list for its non standard curing reason selection for Australian Concrete Samples.
|-
| QPM-1882 || Reduced maximum density screens (1289.5.1.1 & 1289.5.2.1) are now able to be used in Assigned Maximum Density (AS 1289.5.4.2) calculations.
|}

Template:QEST Platform 4.6.3051 - Revision history

Lief.martin: Updated release notes

Stephen.riddell at 06:58, 11 May 2018